External USB 3.0 SSD with Full Disk Encryption

ata encryption, aes256, ASM1053E, ubuntu, linux, external case, caddy, intel 535 series

Preface# External USB drives are everywhere these days, used as storage extension, data transport facility or backup drive. If you need a reliable, schock resistent and secure solution an external SSD might be the best choice instead of an old fashioned hard drive. Especially in case the drive got stolen, a SSD can protect your data […]

HowTo: Wakeup your Synology NAS from Standby/Power Save Mode

timeout, linux, ubuntu, backup, scp, sftp, System Hibernation, backup

Scheduled Backups from Remote Locations#

As poweruser, you may have different servers out there which send their backups to a centralized backup location – in this example, a Synology NAS. The file transfers can be done by ftp, sftp, scp, nfs or another supported protocol.

In case you want to safe energy costs, it possible to enable the power safe mode which turns the system (as well as the HDDs) in standby mode. It can be waked-up by accessing the web-interface or some other file services, but this will take around 30-60s! In most cases, this behaviour will cause a timeout or connection refused error in your backup scripts. To prevent this, you can wake up your NAS before running the backup tasks. The following script tries to access the Web-Interface (DSM) on port 80 for a several times and returns 0 as exit code in case a valid response is returned by the remote server.

Wake-Up Script#


# Synology NAS Wake-up
# ------------------------------------

# hostname/ip set ?
if [ -z "$1" ]; then
    echo "Usage: synology_wakeup.sh <hostname>"
    exit 1

# get the server response. 5 connection tries with 10s delay -> 200s wait
serverResponse=$(wget --quiet --max-redirect=0 --retry-connrefused --timeout=20 --wait=10 --tries 5 --server-response -O /dev/null $1 2>&1)

# http detection pattern (response will be empty on con_refused)
detectionPattern="HTTP/1.1 (200|30[0-8])"

# server online ?
if [[ $serverResponse =~ $detectionPattern ]] ; then
    exit 0
    exit 1


Just run the script by passing the ip addess/hostname to it. On error (non responding nas) the script will return the exit code 1.


# your backup/pre backup script

# wakeup your NAS by its IP/Hostname

# successfull ?
if [ $? -ne 0 ]; then
   echo "ERROR - Synology NAS seems to be offline!"
   exit 1




Firmware Update of IBM ServeRaid BR10i with Ubuntu

system x, x3550 m3, LSI SAS 1068E, ibm 7944

I have just got a used IBM x3550 M3 server as development machine and ran into some trouble when trying to add some SSDs: the throughput was pretty slow (~100MB/s). Generally the BR10i controller supports 3G SATA2 and therefore i expected a throughput of ~250MB. I’ve figured out, that this behaviour is caused by the firmware […]

Ubuntu 15.10 with Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card

mbmi to qmi modeswitch, magical ffc-auth sequence

A several days ago, i’ve replaced the Gobi 2000 WWAN Card with a newer version, a Dell 5570 Module. It’s a branded Sierra Wireless card, so i hoped it will work out of the box on Ubuntu 15.10 – but nothing. After some investigations if figured out, that the card is locked in “low-power” / […]

Ubuntu 15.10 – Disable Wake on LAN (WOL) permanently

ubuntu, systemd, Wily Werewolf, notebook, battery power drain

Preface# In some cases, Wake on LAN is enabled by default and you cannot disable it in your BIOS/UEFI because the setting is not available. On notebooks/ultrabooks, WOL can drain/discharge your battery even your device is powered-off! There are a several guides out there, which didn’t even work. The general mistake is, that the WOL […]